Temperature- and pH-Responsive Schizophrenic Copolymer Brush Coatings with Enhanced Temperature Response in Pure Water.

Novel brush coatings were fabricated with glass surface-grafted chains copolymerized using surface-initiated atom transfer radical polymerization (SI-ATRP) from 2-(2-methoxyethoxy)ethyl methacrylate (OEGMA188) and acrylamide (AAm), taken in different proportions. P(OEGMA188-co-AAm) brushes with AAm mole fraction >44% (determined with XPS and TOF-SIMS spectroscopy) and nearly constant with the depth copolymer composition (TOF-SIMS profiling) exhibit unusual temperature-induced transformations: The contact angle of water droplets on P(OEGMA188-co-AAm) coatings increases by ∼45° with temperature, compared to 17-18° for POEGMA188 and PAAm. The thickness of coatings immersed in water and the morphology of coatings imaged in air show a temperature response for POEGMA188 (using reflectance spectroscopy and AFM, respectively), but this response is weak for P(OEGMA188-co-AAm) and absent for PAAm. This suggests mechanisms more complex than a simple transition between hydrated loose coils and hydrophobic collapsed chains. For POEGMA188, the hydrogen bonds between the ether oxygens of poly(ethylene glycol) and water hydrogens are formed below the transition temperature Tc and disrupted above Tc when polymer-polymer interactions are favored. Different hydrogen bond structures of PAAm include free amide groups, cis-trans-multimers, and trans-multimers of amide groups. Here, hydrogen bonds between free amide groups and water dominate at T < Tc but structures favored at T > Tc, such as cis-trans-multimers and trans-multimers of amide groups, can still be hydrated. The enhanced temperature-dependent response of wettability for P(OEGMA188-co-AAm) with a high mole fraction of AAm suggests the formation at Tc of more hydrophobic structures, realized by hydrogen bonding between the ether oxygens of OEGMA188 and the amide fragments of AAm, where water molecules are caged. Furthermore, P(OEGMA188-co-AAm) coatings immersed in pH buffer solutions exhibit a 'schizophrenic' behavior in wettability, with transitions that mimic LCST and UCST for pH = 3, LCST for pH = 5 and 7, and any transition blocked for pH = 9.

"Command" surfaces with thermo-switchable antibacterial activity.

In the presented work "smart" antibacterial surfaces based on silver nanoparticles (AgNPs) embedded in temperature-responsive poly(di(ethylene glycol)methyl ether methacrylate) - (POEGMA188) as well as poly(4-vinylpyridine) - (P4VP) coatings attached to a glass surface were successfully prepared. The composition, thickness, morphology and wettability of the resulting coatings were analyzed using ToF-SIMS, XPS, EDX, ellipsometry, AFM, SEM and CA measurements, respectively. Temperature-switched killing of the bacteria was tested against Escherichia coli ATCC 25922 (representative of Gram-negative bacteria) and Staphylococcus aureus ATCC 25923 (representative of Gram-positive bacteria) at 4 and 37 °C. In general at 4 °C no significant difference was observed between the amounts of bacteria accounted on the grafted brush coatings and within the control sample. In contrast, at 37 °C almost no bacteria were visible for temperature-responsive coating with AgNPs, whereas the growth of bacteria remains not disturbed for "pure" coating, indicating strong temperature-dependent antibacterial properties of AgNPs integrated into brushes.

Temperature-Controlled Orientation of Proteins on Temperature-Responsive Grafted Polymer Brushes: Poly(butyl methacrylate) vs Poly(butyl acrylate): Morphology, Wetting, and Protein Adsorption.

Poly( n-butyl methacrylate) (PBMA) or poly( n-butyl acrylate) (PBA)-grafted brush coatings attached to glass were successfully prepared using atom-transfer radical polymerization "from the surface". The thicknesses and composition of the PBMA and PBA coatings were examined using ellipsometry and time-of-flight secondary ion mass spectrometry (ToF-SIMS), respectively. For PBMA, the glass-transition temperature constitutes a range close to the physiological limit, which is in contrast to PBA, where the glass-transition temperature is around -55 °C. Atomic force microscopy studies at different temperatures suggest a strong morphological transformation for PBMA coatings, in contrast to PBA, where such essential changes in the surface morphology are absent. Besides, for PBMA coatings, protein adsorption depicts a strong temperature dependence. The combination of bovine serum albumin and anti-IgG structure analysis with the principal component analysis of ToF-SIMS spectra revealed a different orientation of proteins adsorbed to PBMA coatings at different temperatures. In addition, the biological activity of anti-IgG molecules adsorbed at different temperatures was evaluated through tracing the specific binding with goat IgG.

Glass transition in temperature-responsive poly(butyl methacrylate) grafted polymer brushes. Impact of thickness and temperature on wetting, morphology, and cell growth.

Poly(n-butyl methacrylate) (PBMA) grafted polymer brushes attached to glass were fabricated in a three-step process involving surface initiated atom transfer radical polymerization. The surface properties of the coatings after subsequent fabrication steps were confirmed using ToF-SIMS and ellipsometry. Measurements of water contact angle and AFM revealed temperature-induced changes in the hydrophobicity and morphology of the coating. The glass transition temperatures (Tg) of the PBMA coatings with different thicknesses were determined from the AFM measurements. For the PBMA grafted brush coatings with thicknesses less than 62 nm, Tg increases sharply with increasing thickness. The PBMA grafted coatings of thickness equal to 86 nm and 43 nm as well as control glass substrates were used as substrates for culturing a urinary bladder cancer HTB-5 cell line. After 144 h of culturing, a well-developed monocellular layer may be observed on the PBMA coating of thickness equal to 86 nm. In turn, the cells incubated on thinner (43 nm) PBMA coatings as well as on a control glass sample only start to form a confluent layer.

Temperature-Controlled Three-Stage Switching of Wetting, Morphology, and Protein Adsorption.

The novel polymeric coatings of oligoperoxide-graft-poly(4-vinylpyridine-co-oligo(ethylene glycol)ethyl ether methacrylate246) [oligoperoxide-graft-P(4VP-co-OEGMA246)] attached to glass were successfully fabricated. The composition, thickness, morphology, and wettability of resulting coatings were analyzed using X-ray photoelectron spectroscopy, ellipsometry, atomic force microscopy, and contact angle measurements, respectively. In addition, adsorption of the bovine serum albumin was examined with fluorescence microscopy. The thermal response of wettability and morphology of the coatings followed by that of protein adsorption revealed two distinct transitions at 10 and 23 °C. For the first time, three stage switching was observed not only for surface wetting but also for morphology and protein adsorption. Moreover, the influence of the pH on thermo-sensitivity of modified surfaces was shown.

Synthesis and Postpolymerization Modification of Thermoresponsive Coatings Based on Pentaerythritol Monomethacrylate: Surface Analysis, Wettability, and Protein Adsorption.

Properties of novel temperature-responsive hydroxyl-containing poly(pentaerythritol monomethacrylate) (PPM) coatings, polymerized from oligoperoxide grafted to glass surface premodified with (3-aminopropyl)triethoxysilane, are presented. Molecular composition, chemical state, thickness, and wettability are examined with time of flight-secondary ion mass spectrometry (ToF-SIMS), X-ray photoelectron spectroscopy (XPS), ellipsometry, and contact angle measurements, respectively. Temperature-induced changes in hydrophobicity of grafted PPM brushes are revealed by water contact angle and ellipsometric measurements. Partial postpolymerization modification of hydroxyl groups (maximum a few percent), performed with acetyl chloride or pyromellitic acid chloride, is demonstrated to preserve thermal response of coatings. Adsorption of bovine serum albumin to PPM brushes, observed with fluorescence microscopy, is higher than on glass in contrast to similar hydroxyl-containing layers reported as nonfouling. Enhanced and temperature-controlled protein adsorption is obtained after postpolymerization modification with pyromellitic acid chloride.

Temperature and pH dual-responsive POEGMA-based coatings for protein adsorption.

Poly(oligo(ethylene glycol)ethyl ether methacrylate (POEGMA246) coatings were successfully fabricated using novel approach via polymerization from oligoperoxide grafted to premodified glass substrate. Wettability, content and composition of coatings fabricated with different polymerization times were determined using contact angle measurements, ellipsometry and Time of Flight-Secondary Ion Mass Spectrometry (TOF-SIMS). Thermo- and pH-responsive properties of POEGMA246 coatings were found to depend significantly on concentration of the grafted POEGMA246. Coatings fabricated with polymerization time 30 h exhibit not only temperature- but also pH-dependence of wettability. Thermal response of wettability, measured between 20 and 32°C, was prominent at pH 9 and 7 and diminished or was absent at pH 5 and 3, indicating a transition between hydrated loose coils and hydrophobic collapsed chains, blocked at low pH. Protein adsorption, observed by fluorescence microscopy and analyzed semi-quantitatively using integral geometry approach, decreased dramatically for model protein (lentil lectin labeled with fluorescein isothiocyanate) at transition from pH 5 to pH 9, showing only very weak thermal-dependence. Strong protein adsorption response to pH and very weak one to temperature was confirmed by TOF-SIMS and Principal Component Analysis.

Temperature and pH dual-responsive coatings of oligoperoxide-graft-poly(N-isopropylacrylamide): wettability, morphology, and protein adsorption.

Poly(N-isopropylacrylamide) (PNIPAM) coatings attached to glass with novel approach involving polymerization from oligoperoxide grafted to surface with (3-aminopropyl)triethoxysilane exhibit not only temperature- but also pH-dependence of wettability and protein adsorption. Wettability and composition of coatings, fabricated with different polymerization times, were determined using contact angle measurements and Time Of Flight-Secondary Ion Mass Spectrometry (TOF-SIMS), respectively. Thermal response of wettability, measured between 20 and 40°C, was prominent at pH 9 and 7 and diminished or absent at pH 5 and 3. This indicates a transition between hydrated loose coils and hydrophobic collapsed chains that is blocked at low pH. Higher surface roughness and dramatically increased adsorption of model protein (lentil lectin labeled with fluorescein isothiocyanate) were observed with AFM and fluorescence microscopy to occur in hydrophobic phases (at pH 3, for pH varied at constant temperature of 22°C and at ∼33°C, for temperature varied at constant pH 9). Protein adsorption response to pH was confirmed by TOF-SIMS and Principal Component Analysis.